一类非对称椭圆问题瀑布型多重网格法

本将瀑布型多重网格法用于求解非对称椭圆边值问题，数值结果表明算法是有效的。     

溅射功率对多层膜质量的影响

用磁控溅射技术制备薄膜，用X射线衍射研究在基片和靶间距离固定的情况下不同的溅射功率对薄膜结构的影响。结果表明：过低的溅射功率下淀积的薄膜有畸变的X射线衍射特征峰，特征峰强度小，半峰全宽大。而比较高溅射功率得到的薄膜有比较尖锐的X射线衍射特征峰，强度高和半峰全宽非常窄。研究表明，X射线衍射特征峰强度小和半峰全宽大的薄膜结构疏松，而强度高和半峰全宽非常窄的薄膜结构致密。     

基于偶联反应新极谱法测定痕量亚硝酸根的研究——Ⅱ.以苯酚为偶联试剂

本文研究了苯酚在氨性缓冲溶液中与NO_2~--磺胺重氮盐偶联反应的实验条件,建立了一个灵敏快速测定痕量NO_2~-的新方法。NO_2~-离子浓度在1.0×10~(-10)～4.8×10~(-7)g/ml范围内,与峰高呈良好的线性关系.4000倍量NO_3~-存在不干扰.     

一个具有线性约束的Goldfarb方法的改进算法

本文对具有线性约束的非线性规划问题给出一个Goldfarb方法的改进算法,并且在与[1]同样的条件下,给出了算法之超线性收敛性证明.     

Effect of carbon content on the microstructure and the cracking susceptibility of Fe-based laser-clad layer

The laser cladding of Fe-based alloys on a medium carbon steel substrate was performed using a CO₂ laser and Ar shielding gas that was blown into a molten pool. The microstructure and cracking susceptibility of the laser-clad layers were studied in terms of carbon additions. Results show that the small change of the carbon content in the alloy powders can obviously change the microstructure and properties of the layers. When the carbon content is in the range of 0.3–0.4 wt.%, the decrease of the carbon content in alloy powders will increase the hardness and toughness of the layers simultaneously under the same process parameters. As a result, crack-free coatings with high hardness can be obtained. As the carbon content increases from 0.2 wt.% to 0.4 wt.%, the segregation ratio of chromium increases, while the segregation ratios of nickel, manganese, and silicon first decrease and then increase. At the same time, a new designing principle concerning the composition and microstructure has been put forward, and the principal mechanisms of strengthening and toughening of the layers are fine-grain strengthening and low carbon martensitic phase transformation strengthening.     

全同超形变带转动惯量的粒子数守恒计算

利用推转壳模型的粒子数守恒方法计算了超形变(SD)转动带¹⁹²Hg和¹⁹⁴Hg(1,2,3)的带首转动惯量.分析了带首附近的组态结构及带首转动惯量随对力强度的变化.带首转动惯量之差δJ₀对对力强度十分敏感,而对Nilsson能级参数K、μ及形变参数并不敏感.对力及堵塞效应是造成带首转动惯量差别的主要因素.但与正常形变核相比,对力强度似有较大程度减弱.     

矩形片筏基础的挠度分析

工程上对片筏的力学分析，通常采用温克勒地基模型，且假定床基系数是常量。本则认为床基系数是坐标的函数，考虑了具有线性变化床基系数的地基上的片筏，利用伽辽金法求得周边固支片筏在均布荷载作用下的挠度。所得结果颇具一般性且实用价值更高。     

光电光谱法分析钢中钙

本文研究了用光电光谱法测定钢中钙的方法 ,确定了最佳分析条件 ,分析了共存元素的干扰情况。用本方法测定钢中钙 ,具有良好的准确度和精密度 ,结果令人满意。     

焊接自动化专业引入机器人离线编程的教学探索

机器人焊接已成为焊接自动化技术现代化的主要标志。文中通过阐述机器人离线编程系统的组成原理和主流软件，认为须在焊接自动化专业构筑起机器人离线编程的相关课程体系，才可将机器人离线编程技术引入焊接自动化专业。以此提升焊接自动化的理论和实践教学，提高学生的职业技能。     

Value of Optical Bypass in Packet Ring Networks

This paper firstly examines the value of optical bypass scheme in packet ring networks. An Integer Linear Program (ILP) formulation is presented and analytical results under different traffic patterns are given.